PTH Verge Cutter VC1150

The PTH Verge Cutter VC1150 mills overgrown, built-up road edges back so water can drain off the road again. It's a stone-milling machine, not a flail mower, working up to 1,150 mm wide for tractors, wheel loaders, excavators and other carriers from 100 l/min.

  • Mills built-up verges back so water drains off the road
  • Working width up to 1,150 mm, up to 150 mm deep
  • Hydraulic flow from 100 l/min at 200–360 bar
  • All functions controlled hydraulically from the carrier
  • Folds hydraulically to 1,550 mm wide for the road
Technical data
Working widthUp to 1,150 mm
Working depthMax. 150 mm
Oil flowFrom 100 l/min
Pressure200–360 bar
DriveOne side, 6 high-performance V-belts
Tools40
Total width, working2,700 mm
Total width, transport1,550 mm
Dead weightApprox. 1,000 kg

Overview

Over time, verges rise above the road surface as vegetation, soil and deposited material build up. Rainwater can’t drain away to the side, so it sits at the edge of the road, gets into the base and causes frost and edge damage. The PTH Verge Cutter VC1150 mills the verge back and throws the material into the ditch, which restores the drainage and helps the road last.

Milling, not mowing

A flail mower cuts what’s growing on the verge. This takes off the built-up material itself, using technology from PTH’s stone crushers and mulchers, with carbide-tipped fixed tools that cope with harder material too. That makes it a job to do on a regular cycle, because keeping the drainage working costs less than repairing the road later.

Where it’s used

  • Road and path maintenance, on paved and unpaved surfaces.
  • Councils and road owners.
  • Ditch edges and path edges.
  • Agriculture.

It suits road maintenance depots, council fleets, landscape contractors and farmers.

Fitting it to the carrier

For a tractor, wheel loader or mini loader, it comes on a mounting frame with Category 2 attachment and tilt adjustment. For an excavator, a mowing arm or a crane body, an adapter plate and a combination quick-change adapter are available. Support feet hold it safely when it’s taken off.

Run from the seat

The driver adjusts the cutting angle, the discharge angle and the support wheel hydraulically, and switches between work and transport from the seat through an electro-hydraulic control block. It folds onto the carrier for the road, down to 1,550 mm wide.

Construction

The rotor has an overlapping tool arrangement inside replaceable 10 mm Hardox armour, and the tool holders see little wear. Six high-performance V-belts on one side drive it.

Options

For wheel loaders, tractors and mini loaders

  • Front attachment plate for council carriers
  • Tandem support wheel, hydraulically height-adjustable
  • Control block with joystick and PTH Tronic
  • A special RAL paint finish

For excavators, mowing arms and crane bodies

  • Adapter plate for the carrier
  • Combination quick-change adapter
  • A special RAL paint finish

How it compares

The VC1150 is the middle size. The VC900 works up to 900 mm on the same oil flow, and the VC1400 up to 1,400 mm from 120 l/min.

Quick answers

Is the PTH Verge Cutter a flail mower? No. A flail trims vegetation; this mills the raised verge itself, including stony material, back to the level of the road so water can drain.

What hydraulics does it need? From 100 l/min at 200 to 360 bar.

Can I buy the PTH Verge Cutter VC1150 in the UK? Yes. Exc@v8 is the sole UK importer of PTH. Use the form below or call us for pricing and availability.

Get in touch

Speak to Exc@v8 about the PTH Verge Cutter VC1150.

01539 729999

Cookie settings

Choose which cookies this site may use. You can change this at any time from “Cookie settings” at the bottom of every page.